Walther P38
From Wikipedia, the free encyclopedia
| Walther P38 | |
|---|---|
 P38 code AC42. |
|
| Type | semi-automatic pistol |
| Place of origin | Nazi Germany |
| Production history | |
| Designed | 1938 |
| Number built | About 1,200,000 |
| Specifications | |
| Weight | 0.8 kg (unloaded) |
| Length | 216 mm |
| Barrel length | 125 mm |
|
|
|
| Cartridge | 9 mm Parabellum (8 Round Magazine) |
| Caliber | 9 mm Parabellum |
| Action | double action |
| Rate of fire | one shot per trigger pull |
| Muzzle velocity | 350m/s (1,150ft/s) |
| Effective range | ~50m |
| Feed system | 8 round detachable magazine |
The Walther P38 was a 9 mm pistol that was developed by Walther as the service pistol of the Wehrmacht at the beginning of World War II. It was intended to replace the costly Luger P08, the production of which was scheduled to end in 1942.
The P38 concept was accepted by the military in 1938 but production of actual prototype ("Test") pistols did not start until late 1939. Walther began manufacture at their plant in Zella-Mehlis and produced three series of "Test" pistols, designated by a "0" prefix to the serial number. The third series satisfied the previous problems and production for the Heer (German Army) began in mid-1940, using Walther's military production identification code "480". After a few thousand pistols the Heer changed all codes from numbers to letters and Walther was given the "ac" code. All production was performed at the Walther plant until mid- to late 1942 when additional production began at the Mauser plant in Oberndorf (code "byf" until early 1945, then "svw") and at the Spreewerk plant in Hradek nad Nisou, Czechoslovakia ("cyq"). Production continued until the end of the war and into the post war period. The early Walthers, until late 1941, were made to almost commercial standards of fit and polish. As the pressures of war required increased production the exterior finish declined but the operating components of the P38 remained remarkably well made throughout the war, especially at Mauser.
Three firms made components for P38 production:
- Fabrique Nationale-- slides, frames and locking blocks (M or M1)
- Ceska Zbrojovka, CZ (Böhmische Waffenfabrik)-- barrels (fnh)
- Erste Nordböhmische Metallwarenfabrik -- magazines (jvd)
The French manufactured P38 pistols from captured parts at the Mauser factory from May or June of 1945 until 1946. These are identifiable by the presence of a five-pointed star stamped on the slide. Total German production is estimated at more than 1,200,000 pistols. Production of the P38 resumed at a new Walther factory in Ulm, West Germany under the name "Pistol 1" in 1958 for West German Police and the Bundeswehr. It remained in Walther production, in several revised iterations, until the early 1990s.
An improved version of the P38, the Walther P5 was developed after the war, and was adopted by the police services of Rhineland-Palatinate and Baden-Wurtenberg.
[edit] Design
The P38 was the first locked-breech pistol to use a double-action trigger. The shooter could load a round into the chamber, use the de-cocking lever to safely lower the hammer without firing the round, and carry the weapon loaded with the hammer down. A pull of the trigger, with the hammer down, fired the first shot and the operation of the pistol ejected the fired round and reloaded a fresh round into the chamber, all features found in many modern day handguns.
The first designs submitted to the German Army featured a locked breech and a hidden hammer, but the German Army requested that it be redesigned with an external hammer. This led to the subsequent adoption of the P38 in 1940. Several experimental versions were later created in .45 ACP, and .38 Super, but these were never mass-produced. In addition to the 9mm Parabellum version, some 7.65 mm Parabellum versions were also created and sold.
The breech-locking mechanism operates by use of a wedge-shaped locking block underneath the breech. When fired both the barrel and slide recoil for a short distance, where the locking block drives down, disengaging the sliding and arresting the movement of the barrel.
The P38 uses a double action trigger design similar to the earlier Walther PPK's, and a signal pin is located on the slide, which indicates if the weapon is loaded.[1]
[edit] Bibliography
- The Walther P38 Explained (Download) by Gerard Henrotin (H&L Publishing - HLebooks.com - 2005)
[edit] External links
- Walther Handgun Owners Group
- Modern Firearms & Ammunition
- Walther P1 in Parts, only little changes to P38
- Today Value of the vintage Walther P38
| German-made firearms and light weapons of World War II |
|---|
| Side arms (Pistole) |
| Mauser C96 | Luger | Walther P38 | Walther PPK | Sauer 38H | Mauser HSc |
| Rifles & carbines (Gewehr & Karabiner) |
| Karabiner 98k | Gewehr 41 | Gewehr 43/Karabiner 43 | StG44/MP44 | FG42 | StG45(M) | Volkssturmgewehr 1-5 |
| Submachine guns ( Maschinenpistole ) |
| Bergmann MP18 | MP38/MP40 "Schmeisser" | MP3008 "Volks MP" |
| Machine guns & other larger weapons |
| MG08 | MG34 | MG42 | Faustpatrone | Panzerfaust | Panzerschreck
Flammenwerfer 35 | Panzerbüchse 39 | Granatwerfer 36 | Granatwerfer 42 |
| Notable foreign-made infantry weapons |
| P.640(b) | Vis.35 | Vz.24/G24(t) | MG26(t) | Panzerbüchse 35(p) |
| German-made cartridges used by the Wehrmacht |
| 7.92 x 57 mm | 7.63 x 25 mm Mauser | 7.92 mm Kurz | 7.65 mm Luger | 9 mm Luger |
