Compact Cassette

From Wikipedia, the free encyclopedia

Compact Cassette

Typical 60-minute Compact Cassette
Media type:	magnetic tape
Encoding:	analog signal
Capacity:	23 minutes per side (C46) 30 minutes per side (C60) 45 minutes per side (C90) 50 minutes per side (C100) 60 minutes per side (C120)
Read mechanism:	tape head
Write mechanism:	magnetic recording head
Usage:	audio and data storage

The Compact Cassette, often referred to as audio cassette, cassette tape, cassette, or simply tape, is a magnetic tape sound recording format. Although it was originally intended as a medium for dictation, improvements in fidelity led the Compact Cassette to supplant reel-to-reel tape recording in most non-professional applications.^[1] Its uses ranged from portable audio to home recording to data storage for early microcomputers. Between the 1970s and early 1990s, the cassette was one of the three most common formats for prerecorded music, alongside the LP and later the Compact Disc.^[2]

Compact Cassettes consist of two miniature spools, between which a magnetic tape is passed and wound. These spools and their attendant parts are held inside a protective plastic shell. Two stereo pairs of tracks (four total) or two monaural audio tracks are available on the tape; one stereo pair or one monophonic track is played or recorded when the tape is moving in one direction and the second pair when moving in the other direction. This reversal is achieved either by manually flipping the cassette or by having the machine itself change the direction of tape movement ("auto-reverse").^[3]

[edit] History

Philips introduced the compact audio cassette medium for audio storage in Europe in 1963, and in the United States in 1964, under the trademark name Compact Cassette. Although there were other magnetic tape cartridge systems at the time, the Compact Cassette became dominant as a result of Philips's decision (in the face of pressure from Sony) to license the format free of charge. It went on to become a popular (and re-recordable) alternative to the turntable for LP records during the 1970s.^[2]

[edit] Introduction of music cassettes

The mass production of compact audio cassettes began in 1964 in Hanover, Germany. Prerecorded music cassettes (also known as Musicassettes; M.C. for short) were launched in Europe in late 1965. The Mercury Record Company, a U.S. affiliate of Philips, introduced Musicassettes to the U.S. in September 1966. The initial range consisted of 49 titles.^[4]

However, the system had been initially designed for dictation and portable use, with the audio quality of early players not well suited for music. Some early models also had unreliable mechanical design. In 1971 the Advent Corporation introduced their Model 201 tape deck that combined Dolby type B noise reduction and chromium dioxide (CrO₂) tape. This resulted in the format being taken more seriously for musical use, and started the era of high-fidelity cassettes and players.^[1]

1979 Sony Walkman

During the 1980s, the cassette's popularity grew further as a result of portable pocket recorders and hi-fi players such as Sony's Walkman, which used a body not much larger than a cassette tape, with mechanical keys on one side, or electronic buttons or display on the face. Some would partially collapse if they were not actually holding a cassette. As the transistor radio defined small music in the 1960s, the portable CD player in the 1990s, and the MP3 player in the 2000s, so did the Walkman define very small portable music in the 1980s, with cassette sales overtaking those of LPs.^[5][2] Total vinyl record sales remained higher well into the 1980s due to greater sales of singles, although cassette singles achieved popularity for a period in the 1990s.^[5]

Apart from the purely technical advances cassettes brought, they also served as catalysts for social change. Their durability and ease of copying helped bring underground rock and punk music behind the Iron Curtain, creating a foothold for Western culture among the younger generations.^[6] For similar reasons, cassettes became popular in developing nations.

One of the most famous political uses of cassette tapes was the dissemination of sermons by the Ayatollah Khomeini throughout Iran before the 1979 Iranian revolution, in which Khomenei urged the overthrow of the regime of the Shah.

In 1970s India, they were blamed for bringing unwanted secular influences into traditionally religious areas. Cassette technology created a booming market for pop music in India, drawing criticism from conservatives while at the same time creating a huge market for legitimate recording companies and pirated tapes.^[7] In some countries, particularly in the Third World, cassettes still remain the dominant medium for purchasing and listening to music.^[8]

[edit] Decline

In many western countries, the market for cassettes has declined sharply since its peak in the late 1980s. This has been particularly noticeable with pre-recorded cassettes, whose sales were overtaken by those of CDs during the early 1990s. By 1993, annual shipments of CD players had reached 5 million, up 21% from the year before, while cassette player shipments had dropped 7% to approximately 3.4 million.^[9] The decline continued such that in 2001 cassettes accounted for only 4% of all music sold in the United States.^[10] Since then, the pre-recorded market has undergone further decline, with few retailers stocking them because they are no longer issued by the major music labels.^[8] However, as of late 2006, blank cassettes are still being produced and are sold at many retail stores, and facilities for cassette duplication remain available. Cassette recorders and players are gradually becoming more scarce, but are still widely available and are still a regular feature of Hi-Fi systems.^[11]

Despite the wide availability of higher-fidelity media, cassettes also remain popular for specific applications, including car audio and other difficult environments. Cassettes and their players are typically more rugged and resistant to dust, heat and shocks than most digital media (especially CDs). Their lower fidelity is not considered a serious drawback inside the typically noisy automobile interior. Although the "shock proof" buffering technology in many new CD players allows time to recover from intermittent skips, the cassette remains more resilient in the face of periodic and repeated shocks. However, cassettes generally have poor resistance to the excessive levels of heat encountered in parked cars during summer.

While digital voice recorders are now common, Compact Cassette (or frequently microcassette) recorders tend to be cheaper and of sufficient quality to serve as adjuncts or substitutes for note taking in business and educational settings. Audiobooks, church services, and other spoken word material are still frequently sold on cassette, as lower fidelity is generally not a drawback for such content. While most publishers sell CD audiobooks, they usually also offer a cassette version at a lower price. In the audiobooks application, where recordings may span several hours, cassettes also have the advantage of holding up to 120 minutes of material whereas the average CD holds less than 80.^[11]

While cassettes and related equipment have become increasingly marginal in commercial music sales, recording on analog tape remains a desirable option for some. In 2002, Imation received an US$11.9 million grant from the U.S. National Institute of Standards and Technology for research into increasing the data capacity of magnetic tape.^[12] Some musicians still prefer to record their masters on magnetic tape for artistic reasons, and some consumers prefer to buy cassettes for the richness of analog sound.^[11][13]

[edit] Features of the cassette

The cassette was a great step forward in convenience from reel-to-reel audio tape recording, though because of the limitations of the cassette's size and speed, it initially compared poorly in quality. Unlike the open reel format, the two stereo tracks lie adjacent to each other rather than a 1/3 and 2/4 arrangement. This permitted monaural cassette players to play stereo recordings "summed" as mono tracks and permitted stereo players to play mono recordings through both speakers. The tape is 3.81 mm (or 0.150 in.) wide, with each stereo track 0.6 mm wide and an unrecorded guard band between each track. The tape moves at 4.76 cm/s (1⅞ in/s) from left to right.^[14] For comparison, the typical open reel format in consumer use was ¼ inch (6.35 mm) wide, each stereo track nominally ¹⁄₁₆ inch (1.59 mm) wide, and running at either 3¾ or 7½ inches per second (9.5 or 19 cm/s).

[edit] Cassette types

Notches on the top surface of the audio cassette indicate its type. The top cassette, with only write protect notches (here covered by write protect tabs), is a Type I. The next cassette down, with additional notches adjacent to the write protect notch, is a Type II. The bottom two cassettes, featuring the Type II notches plus an additional pair in the middle of the cassette are type IV (metal); note the removal of the tabs on the second of these, meaning the tape is write-protected.

The original magnetic material was based on gamma ferric oxide (Fe₂O₃). Circa 1970, 3M Company developed a cobalt volume-doping process combined with a double-coating technique to enhance overall tape output levels. This product was marketed as "High Energy" under its Scotch brand of recording tapes.^[15] Inexpensive cassettes are commonly labeled "low-noise", but typically are not optimized for high frequency response.

At about the same time chromium dioxide (CrO₂) was introduced by BASF,^[16] and then coatings using magnetite (Fe₃O₄) such as TDK's Audua were produced in an attempt to approach the sound quality of vinyl records. Cobalt-adsorbed iron oxide (Avilyn) was introduced by TDK in 1974 and proved very successful. Finally pure metal particles (as opposed to oxide formulations) were introduced in 1979 by 3M under the trade name Metafine. The tape coating on most Cassettes sold today as either "Normal" or "Chrome" consists of Ferric Oxide and Cobalt mixed in varying ratios (and using various processes); there are very few cassettes on the market that use a pure (CrO₂) coating.^[2]

Simple voice recorders are designed to work with standard ferric formulations. High fidelity tape decks are usually built with switches or detectors for the different bias and equalization requirements for high performance tapes. The most common, iron oxide tapes (defined by an IEC standard as "Type I"), use 120 µs playback equalization, while chrome and cobalt-absorbed tapes (IEC Type II) require 70 µs playback equalization. The recording "bias" equalizations were also different (and had a much longer time constant). Sony tried a dual layer tape with both ferric oxide and chrome dioxide known as 'ferrichrome' (FeCr) (IEC Type III) but these were only available for a short time in the 1970s. Metal Cassettes (IEC Type IV), also use 70 µs playback equalization, and provide still further improvements in sound quality, as well as improved resistance to wear.^[15] The quality is normally reflected in the price; Type I cassettes are generally cheapest, and Type IV usually the most expensive. BASF developed a chrome cassette designed for use with 120 µs (type I) playback equalization but this idea only caught on for commercially pre-recorded cassettes.^[2]

Notches on top of the cassette shell indicate the type of tape within. Type I cassettes only have write-protect notches, Type II have an additional pair next to the write protection ones, and Type IV (metal) have a third set in the middle of the cassette shell. These allow cassette decks to automatically detect the tape type and select the proper bias and equalization. Some inexpensive models may lack this feature. Playback of Type II and IV tapes on such a player will produce exaggerated treble, but it may not be noticable because typically such devices have amplifiers that lack extended high frequency output.

[edit] Playback length

Cassettes of varying tape quality and playing time

Tape length is usually measured in minutes of total playing time. The most popular varieties are C46 (23 minutes per side), C60 (30 minutes per side), C90, and C120. The C46 and C60 lengths are typically 15–16 µm thick, but C90s are 10–11 µm and C120s are just 9 µm thick, rendering them more susceptible to stretching or breakage. Some vendors are more generous than others, providing 132 meters or 135 meters rather than 129 meters of tape for a C90 cassette. C180 and even C240 tapes were available at one time, but these were extremely thin and fragile and suffered badly from effects such as print-through, which made them unsuitable for general use. Other lengths are (or were) also available from some vendors, including C10 and C15 (useful for saving data from early home computers), C30, C50, C54, C64, C70, C74, C80, C84, C100, C105, and C110.^[15]

Some companies included a complimentary blank cassette with their portable cassette recorders in the early 1980s. Panasonic's was a C14 and came with a song recorded on side one, and a blank side two. Except for C74 and C100, such non-standard lengths have always been hard to find, and tend to be more expensive than the more popular lengths. Home taping enthusiasts may have found them useful for fitting an album neatly on one or both sides of a tape. For instance, the initial maximum playback time of Compact Discs was 74 minutes, explaining the relative popularity of C74 cassettes.

Inside a cassette. "Supply reel" and "takeup reel" are from the point of view of the player looking at the back of the cassette: when viewed from the front of the machine, the tape "plays" from left to right (though of course an auto-reverse deck can play in either direction). The tape is pressed into close contact with the head by the pressure pad; guide rollers help keep the tape in the correct position. Smooth running is assisted by a slippery liner between the spools and the shell; here the liner is transparent. The magnetic shield reduces pickup of stray signals by the heads of the player.

[edit] Write-protection

All cassettes include a write protection mechanism to prevent re-recording and accidental erasure of important material. Each side of the cassette has a plastic tab on the top that may be broken off, leaving a small indentation in the shell. This indentation allows the entry of a sensing lever that prevents the operation of the recording function when the cassette is inserted into a cassette deck. If the cassette is held with one of the labels facing the user and the tape opening at the bottom, the write-protect tab for the corresponding side is at the top-left.

If later required, a piece of adhesive tape can be placed over the indentation to bypass the protection, or (on some decks), the lever can be manually depressed to record on a protected tape. Extra care is required to avoid covering the the additional indents on high bias tape cassettes adjacent to the write-protect tabs.

[edit] Cassette players and recorders

The first cassette machines were simple mono recorders, which could also play. Early machines required attaching an external dynamic microphone. Most units after the 1970s also incorporated built-in condenser microphones, which have extended high frequency response, but may also pick up noises from the recorder motor. A common portable recorder format still common today is a long box, the width of a cassette, with a speaker at the top, a cassette bay in the middle, and "piano key" controls at the bottom edge. The markings of "piano key" controls near the handle were soon standardized and this legacy still emulated on many software control panels, though many DVD panels have eliminated the fast forward and rewind buttons in favor of next and previous tracks, which are only implemented on machines which have logic to search for blank spots in the tape. These symbols are commonly the square for stop, right pointing triangle for play, double triangles for fast forward and rewind, red dot for record, and the pause button. Another format is only slightly larger than the cassette, also adapted for stereo "Walkman" player applications.

Main article: Cassette deck

A typical portable desktop cassette recorder from RadioShack.

Stereo recorders eventually evolved into high fidelity and were known as "cassette decks", after the reel-to-reel "decks". Many formats of cassette players and recorders have evolved over the years. Initially all were top loading, usually with cassette on one side, VU meters and recording level controls on the other side. Older models used combinations of levers and sliding buttons for control.

Nakamichi RX-505 audio cassette deck

A major innovation was the front-loading arrangement. Pioneer's angled cassette bay and the exposed bays of some Sansui models were eventually standardized as a front-loading door into which a cassette would be loaded. Later models would adopt electronic buttons, and replace conventional meters (which could be "pegged" when overloaded) with electronic LED or fluorescent displays, with level controls typically either being controlled by rotary controls or side-by-side sliders. BIC briefly offered models which could be run at double speeds, but Nakamichi was widely recognized as one of the first companies to create decks which rivaled reel-to-reel decks with frequency response from the full 20-20,000 Hz range, low noise, and very low wow and flutter.^[17][18]

As they became aimed at more casual users, fewer decks had microphone inputs. Dual decks became popular and incorporated into home entertainment systems of all sizes for tape dubbing. Although the quality would suffer each time a source was copied, there are no mechanical restrictions on copying from a record, radio, or another cassette source. Even as CD recorders are becoming more popular, some incorporate cassette decks for professional applications.

An assortment of boomboxes

Another format that made an impact on culture in the 1980s was the "boom box" which combined the portable cassette deck with speakers capable of producing significant sound levels. The boom box became synonymous with urban youth culture in entertainment, which led to the somewhat derisive nickname "ghetto blaster".

Applications for car stereos varied widely. Auto manufacturers in the U.S. would typically fit a cassette slot into their standard large radio faceplates. Europe and Asia would standardize on DIN and double DIN sized faceplates. In the 1980s, a high end installation would have a Dolby AM/FM cassette deck, and they rendered the 8-track cartridge obsolete in car installations because of space, performance and audio quality. As the cost of building CD players declined, many manufacturers a CD player, but some cars, especially those targeted at older drivers still offer the option of a cassette player, either by itself, or sometimes in combination with a CD slot. The newest cars often are not designed to accommodate any cassette drive, but the auxiliary jack advertised for MP3 players can also be used with portable cassette players.

A head cleaning cassette

Although the cassettes themselves were relatively durable, the players required regular maintenance to perform properly. Head cleaning may be done with long swabs, or cassette-shaped devices that could be inserted into a tape deck to polish the heads and remove smudges and dirt. Similarly shaped demagnetizers used magnets to degauss the deck, which kept sound from becoming distorted. A common mechanical problem occurred when a worn-out or dirty player rotated the supply spool faster than the take-up spool or failed to release the heads from the tape upon ejection. This would cause the magnetic tape to be fed out through the bottom of the cassette and become tangled in the mechanism of the player. In these cases the player was said to have "eaten" the tape, and it often destroyed the playability of the cassette altogether, and resulted in the common sight of tangled tape on the side of the road. ^[19] Cutting blocks, analogous to those used for open reel 1/4" tape, were readily available though, but mainly used for retrieving valued recordings, through removing the damaged portion of, or repairing the break in, the tape. Creation of compilations was usually by re-recording rather than splicing sections of songs because of the much smaller tape area.

[edit] Applications

[edit] Audio

The Compact Cassette was originally intended for use in dictation machines. In this capacity, some later-model cassette-based dictation machines could also run the tape at half speed (¹⁵⁄₁₆ in/s) as playback quality was not critical. The Compact Cassette soon became a popular medium for distributing prerecorded music—initially through The Philips Record Company (and subsidiary labels Mercury and Philips in the U.S.). As of 2006, one finds cassettes used for a variety of purposes such as journalism, oral history, meeting and interview transcripts and so on. However, they are starting to give way to Compact Discs and more "compact" storage media.

[edit] Home studio

In the 1980s, Tascam introduced the Portastudio line of four and eight-track cassette recorders for home studio use. In the simplest configuration, rather than playing a pair of stereo channels of each side of the cassette, the typical "portastudio" used a four-track tape head assembly to access four tracks on the cassette at once (with the tape playing in one direction). Each track could be recorded to, erased or played back individually, allowing amateur musicians (and some professionals) to overdub themselves and create simple multitrack recordings easily, which could then be mixed down to a finished stereo version on an external machine. To increase audio quality in these recorders, the tape speed is sometimes doubled in comparison to the standard; additionally, dbx, Dolby B or Dolby C noise reduction provides compansion (compression of the signal during recording and equal & opposite expansion of the signal during playback), which yields increased dynamic range by lowering the noise level and increasing the maximum signal level before distortion occurs. Multi-track cassette recorders with built-in mixer and signal routing features provide a wide range of features and benefits from easy-to-use beginner units up to professional level recording systems.^[20] Although professional musicians usually only used multitrack cassette machines as "sketchpads", an exception is Bruce Springsteen's "Nebraska" which was recorded entirely on a Portastudio.

[edit] Home dubbing

Home Taping is Killing Music. (And It's Illegal)

Most cassettes were sold blank and used for recording (dubbing) the owner's records (as backup or to make mixtape compilations), their friends' records or music from the radio. This practice was condemned by the music industry with such slogans as "Home Taping is Killing Music". However, many claimed that the medium was ideal for spreading new music and would increase sales, and strongly defended at least their right to copy their own records onto tape. For a limited time in the early 1980s Island Records sold chromium dioxide “One Plus One” cassettes that had an album prerecorded on one side and the other was left blank for the purchaser to use. Cassettes were also a boon to people wishing to tape concerts (unauthorized or authorized) for sale or trade, a practice tacitly or overtly encouraged by many bands with a more counterculture bent such as the Grateful Dead. Blank Compact Cassettes also were an invaluable tool to spread the music of unsigned acts, especially within Tape trading networks.

Various legal cases arose surrounding the dubbing of cassettes. In the UK, in the case of CBS Songs v. Amstrad (1988), the House of Lords found in favor of Amstrad that producing equipment that facilitated the dubbing of cassettes, in this case a high-speed twin cassette deck that allowed one cassette to be copied directly onto another, did not constitute the infringement of copyright.^[21] In a similar case, a shop owner who rented cassettes and sold blank tapes was not liable for copyright infringement even though it was clear that his customers were likely dubbing them at home.^[22] In both cases, the courts held that manufacturers and retailers could not be held accountable for the actions of consumers.

As an alternative to home dubbing, in the late 1980s, the Personics company installed booths in record stores across America which allowed customers to make personalised mixtapes from a digitally-encoded back-catalogue with customised printed covers.

[edit] Data recording

A C2N Datassette recorder for Commodore computers

German-made cassettes sold for computer data recording, circa 1980

The Hewlett Packard HP 9830 was one of the first desktop computers in the early 1970s to use automatically controlled cassette tapes for storage. It could save and find files by number, using a clear leader to detect the end of tape. These would be replaced by specialized cartridges such as the 3M DC-series. Many of the earliest microcomputers implemented the Kansas City standard for digital data storage. Most home computers of the late 1970s and early 1980s could use cassettes for data storage as a cheaper alternative to floppy disks, though users often had to manually stop and start a cassette recorder. Even the first version of the IBM PC of 1981 had a cassette port and a command in its ROM BASIC programming language to use it. However, this was seldom used, as even then floppy drives had become commonplace in high-end machines. Data cassette tapes were even used to control the high-end Omnibot robots from Japanese toy company Tomy.

The typical encoding method for computer data was simple FSK which resulted in typical data rates of 500 to 2000 bit/s, although some games used special faster loading routines, up to around 4000-bit/s. A rate of 2000-bit/s equates to a capacity of around 660 kilobytes per side of a 90-minute tape.

Among home computers that primarily used data cassettes for storage in the late 1970s were Commodore PET (early models of which had a cassette drive built-in), TRS-80 and Apple II Plus, until the introduction of floppy disc drives and hard drives in the early 1980s made cassettes virtually obsolete for day-to-day use. However, they remained in use on some portable systems such as the TRS-80 Model 100 line until the early 1990s. They were also popular in the UK, whose 8-bit software market remained largely cassette-based until it too disappeared altogether in the early 1990s.

The use of better modulation techniques like QPSK or those used in modern modems, combined with the improved bandwidth and signal to noise ratio of newer cassette tapes, allowed much greater capacities (up to 60 MB) and speeds (10–17 kB/s for data rate) on each cassette. These were typically used as hard disk backup for PCs in the late 1980s. They also found use during the 1980s in data loggers for scientific and industrial equipment.

In 1982 the video game developer Starpath (formerly Arcadia Inc.) released the Starpath Supercharger, an interface device that allowed their Atari 2600 games to be distributed on cassette, allowing for increased RAM and larger games.

[edit] Successors

A Compact Cassette and a microcassette

Technical development of the cassette effectively ceased when digital recordable media such as DAT and MiniDisc were introduced in the late 1980s and early 1990s. Anticipating the switch from analog to digital, major companies such as Sony shifted their focus to new media.^[23] In 1992, Philips introduced the Digital Compact Cassette (DCC), a DAT-like tape in the same form factor as the compact audio cassette. It was aimed primarily at the consumer market. A DCC deck could play back both types of cassettes. Unlike DAT, which was accepted in professional usage because it could record without lossy compression effects, DCC failed in both home and mobile environments, and was discontinued in 1996.^[24]

The microcassette has in many cases supplanted the full-sized audio cassette in situations where voice-level fidelity is all that is required, such as in dictation machines and answering machines. Even these, in turn, are starting to give way to digital recorders of various descriptions.^[25] Since the rise of cheap CD-R discs, and flash memory-based digital audio players, the phenomenon of "home taping" has effectively switched to recording to Compact Disc or downloading from commercial or music sharing websites.^[26]

Because of consumer demand, the cassette has remained influential on design nearly two decades after its decline. As the Compact Disc grew in popularity, cassette-shaped audio adapters were developed to provide an economical and clear way to obtain CD functionality in vehicles equipped with cassette decks. A portable CD player would have its analog line-out connected to the adapter, which in turn fed the signal to the head of the cassette deck. These adapters continue to function with MP3 players as well, and are generally more reliable than the FM transmitters that must be used to adapt CD players to MP3s. MP3 players shaped as audio cassettes have also become available, which can be inserted into any tape player and communicate with the head as if they were normal cassettes.^[27][28]

[edit] Repair

Cassettes contain moving parts such as rollers which can become worn, leading to jamming or breakage of the magnetic tape itself. This need not spell the end of a valuable recording: one can extract the tape from the shell of its cartridge and transplant it into a new cartridge. "Eaten" tapes as described above can in many cases also be rescued after running the tapes' back side over a rounded surface such as a pen to re-flatten it as best as possible. A crude repair can even be performed on a severed tape by carefully aligning and reattaching the strand ends against a backing of special mylar splicing tape (normal adhesive tape should never be used on audio recording tape because the adhesive will "bleed" over time), then trimming excess on either side with scissors or a precision knife, enabling a basic playback such as for dubbing out to a digital recording source as on a personal computer.

Better-made compact cassettes are held together by a number of screws, so that they may be disassembled and reassembled. It may be helpful to practice the procedure on blank cassettes first. Care should be taken to ensure that the tape follows the correct path through the cassette before reassembly, and that all of the small parts are in their proper places. If the original, worn cassette is glued together instead of held together by screws, it can be cracked progressively open by inserting a thin blade of metal (such as a screwdriver or knife blade) in the seam between the halves of the cassette shell, while exercising care not to gouge or damage the reels.

The spools upon which the tape is wound are often slotted so that the end of the tape may be freed from one spool and secured to a new spool.

Two other common problems with cassette tapes are: 1) the tape winds unevenly inside the plastic case over time which gives rise to jamming during playback or rewinding, and 2) the felt pressure pad that contacts the magnetic tape eventually falls off. Two solutions: 1) slap the cassette on a flat surface several times and then rewind the tape all the way through without pause (this may have to be tried several times). 2) replace the part composed of the copper and felt pressure pad unit from an unused cassette tape.

[edit] See also

Wikimedia Commons has media related to:

Compact audio cassette

• Cassette culture
• Cassette single
• Digital cassettes
• 8-track cartridge
• Elcaset
• Electronic journalism
• Home Taping is Killing Music
• List of audio formats
• Microcassette
• Minicassette
• Mix tape
• Pocket Rockers
• PXL-2000
• VHS

[edit] References

[edit] External links

• Photos of many brands of Cassettes
• Reviews and comparisons of various cassette types
• Technical data and photographs of vintage cassette decks
• A brief history of the recording media industry
• Collectible Cassette Music Tapes
• Discography showing example of One Plus One cassette
• Tape recording and playback concepts